ECO-65 PELLET STOVE

What is a pellet stove and what is pellet fuel? A pellet stove is a heating appliance, which burns pellet fuel fed by an auger system. Pellet stoves work on the same principles as wood stoves, except for the fact they are environmentally friendly and burn more efficiently. Wood pellet fuel is comprised of compressed sawdust and ground wood chips. Why do I have two air dampers? One in the front and one on the left-hand side? The rod in the front of the stove is the tube exchange cleaner – not an air damper. It is used to scrape the heat exchanger clean. After unplugging and cooling the stove, lift off the top heat shield, close the door, and pull the rod back and forth a few times. This allows any build-up of ash to fall into the ashtray.

Can you hook up a pellet stove to ductwork

Our busy schedules, an aging population and having other high tech products in our lives, make pellet stove usage seem like a natural move. There is a price to pay for all that convenience. Pellet stoves are high maintenance. There are basic differences between pellet stoves and other solid fuel appliances. Woodstoves are negative draft appliances using the natural draft of a chimney to extract the products of combustion.

Pellet stoves are positive draft appliances using a fan to blow the exhaust up and out the vent.

ducting fresh air to wood stove–danger? (post #) I bought the “outside air adapter” from Vermont Castings and would like to hook it up to the duct, but would like to know more about this problem. but we did have a shroud around the stove, and ran a duct up to the cold air return on the furnace. put a block out switch on the.

The sheet covers stoves with cast housing, as well as machined pictures and explanation included.. It mixes well with the cool air from down low with no excessive concentration of super hot air in just one area. What are these three buttons at the bottom of my pellet stoves control board? How do I replace the exhaust combustion blower on my stove? Next, the two thermostat lead wires should be connected at this location and the screws tightened; the jumper wire should be saved for future operation without a thermostat.

If it becomes necessary to replace the convection blower, Click Here for an instruction sheet detailing this procedure. Also be sure to follow all other maintenance instructions as outlined in your Owners Manual and the Instructional DVD included with the unit. Hello, I have an ashton bay pellet stove,after stopping the stove to clean,and restarting burn pot filled up and smoke appeared but the exhaust fan did not start. Supply power from the outlet directly to the blower and it should run on high without surging up and down.

Many customers have called us or emailed us and have asked this question.

Azubi speed dating essen –

This is recommended by Vermont Castings for tightly constructed homes for two reasons–better stove performance and to avoid having negative pressure potentially affecting the draft of the stove, particulary if you’re running exhaust fans and the like. I gather it’s even possible to reverse the draft and suck smoke into the house this way. But the local VC dealer told me that at a recent conference he attended there was major controversy about housefires attributed to fresh air inlets, particularly when the ducts were PVC.

According to him, the Canadians are no longer requiring fresh air ducts in their code for new construction because of this.

Reinvent the way you heat your home with Castle’s Serenity wood pellet stove and new Smart Controller. The Smart Controller allows you to choose manual, thermostat, and weekly operational modes to heat your home on your schedule.

Vertical distance Elevation where you live. A rule of thumb equation we are using has been adopted by most pellet manufactures. All of the above mentioned venting restrictions have been assigned EVL values as follows: If your installation is below ft, we would need to do some math. The rule of thumb equations is that if the sum of the EVL is 15 or greater, then the pellet vent pipe would be increased to 4 inch diameter pellet vent pipe. Of course there may be different variables to this equation that we used, but still it works quite well.

Let’s try out this equation using several different typical installation configurations we encounter. The first typical installation is out the back of the stove and straight through the wall with 10 to 12 inches protruding chimney past the outside wall with an installation altitude of less than ft. Do make sure that the pipe outside is clear of walkways, shrubs, and at least 24 inches above the ground. Looking back at our chart, we know that each horizontal foot equals 1 EVL.

For this installation we have about 2 and no more than 3 horizontal feet which equals to no more than 3 EVL.

Valuable information from the Wood Pellet Institute.

View yuri’s Album You should check with your house ins co if there is a higher premium for them. There is for wood stoves as they are higher risk. May need a special chimney. I would wait till that pellet plant is up and running and stable. There was a straw bale plant and manufacturing facility by Portage la Prairie and farmers were burning straw. They made funiture from some process from it and then it went broke.

The Thermostat System is a digital box with a low fire setting (that you can vary) and a high fire setting (that you can vary) that adjusts the stove through a wall thermostat. You set your wall thermostat to whatever temperature you want it and the thermostat system controls the stove.

A chimney installation for a pellet stove is a process that is handled by an experienced installer. That is because the installation of a pellet stove involves the creation of an outlet for the pellet stove in order to vent the heat exchange that is taken place. This is accomplished either through creating a horizontal direct ventilation or vertical direct ventilation. Having a pellet stove chimney installation completed for your home should be done by an installer who is certified by the National Fireplace Institute NFI.

Having a NFI certified installer removes much of the doubts or problems that can occur with an installation and protect you and your problem from any harm that would be caused by an improper installation of your pellet stove chimney. This article will explain some of the process involved in the installation of a pellet stove chimney that is used by the installer. Determining Type of Installation for the Chimney The first step in the process for the installation of your pellet stove chimney is determining how the chimney will be installed.

How to Install a Gas Stove – Without Dangerous Leaks

The cost of wood for wood burning stoves can fluctuate each year depending on availability. Many modern families are switching to the convenience of pellet stoves, which most often use corn kernels or tiny compressed wood pellets as a source of heat energy. Pellet stoves can sufficiently heat large buildings such as warehouses and office buildings or can be used to heat smaller rooms such as the family den or a master bedroom.

The main advantage of pellet stove heating is the low price.

Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. 1 You can set the timer to the length of time you want the GAS Fireplace, AGP Pellet Stove or GAS Insert to operate (1 to minutes). 2 Press the “TIMER” button once. The Timer display “” will blink.

Northern Ontario amc said: There are a few of us Fahrenheit owners here, as well as a group of very knowledgeable pellet burners. I hooked mine up as an add on to my oil furnace. I don’t have my manual handy, but I believe there are illustrations that show where the backdraft dampers would go. Those will keep the heat from ‘looping’ through the hot supply and cold return ducts.

I have one damper in the oil furnace above my AC a-coil and a butterfly damper in the outlet of the Fahrenheit. The damper in my oil furnace is a home brew unit, but it does the trick.

The complete source for building, designing, and remodeling green homes

This is the first “wood furnace” I’ve had but I’ve had wood stoves so wood is nothing new. Here is the issue that has me perplexed, the thing just won’t make heat. Trying to heat sqf block shop with I’d give it R10 on the roof. I have a fisher wood stove in there, thing gets the place way better than outside, I figured with a larger wood furnace I could tie into the hot air ducts and get a more even heat at the LEAST make the same temp but faster

Do you realize there is an entire field of woodstoves that the general public rarely hears about, even though there are specialty woodstove stores in every town and woodstove displays in most hardware and building supply outlets.

Background and history[ edit ] Modern pellet stove cross section Scrap wood and ship-lap burners have been around since at least the early 20th century easily seen in the use of barrel stoves, braziers, and oil drum fires in depression-era Hooverville historical media. Professionally built wood-fired ovens with sawdust hoppers were used in the early part of the 20th century.

All of these units used scrap wood or sawdust. In , the Presto-Log was invented reusing scrap sawdust from the Potlatch pine mill in Lewiston, Idaho for domestic heat. From this came the miniaturized pellet stove, which emerged from Washington State in the s. The pellet stove changed in appearance over the years from a simple, boxy workhorse design, to a modern heating appliance. Pellet stoves can be either free standing units or fireplace inserts vented into an existing chimney.

Most pellet stoves are constructed using large, heat conductive, steel or cast-iron pieces, with stainless steel to encase circuitry and exhaust areas. Pellet furnaces and pellet boilers are also available in addition to the decorative stove. These units can be retrofitted into existing home heating systems with only minor changes to existing ductwork and or plumbing. The heating industry has considerably shifted toward biomass stoves and heating devices based on efficient combustible and renewable resources.

Even so, pellet stoves have become a viable, economical, and popular option for home heating systems only in the last ten years. Method[ edit ] The pellet fuel is delivered from the storage facility or the day tank single stoves into the combustion chamber. With the heat generated, circuit water is heated in the pellet boiler.

How pellet furnaces and stoves can revitalize the way you heat your home

Where do you need services? Go Where do you need services? Go What service do you need? Which service are you interested in? You understand that they may use automated phone technology to call you, and your consent is not required to purchase products or services.

Nov 25,  · Help Using Pellet Stove to Heat Oil Fired Hot Water Basebord [HVAC] Woodchuck wood furnace not making heat It did have a box on the back to hook up to existing duct work I .

Thought for the Harvest: Choosing the Right Stove for Your Home Why a pellet stove might be the best option for heating your outbuilding Cabin fever: Considering fireplace and stove options for your home away from home How pellet furnaces and stoves can revitalize the way you heat your home When you think of wood heat, you might picture sitting around the fireplace, with most of the heat coming directly from the burning logs and the hearth. While that might bring cozy memories and warm thoughts, wood pellet furnaces and stoves provide more than just a cozy place to sit — they can revitalize the way you heat your entire home.

Units like the Magnum can heat any house up to 3, square feet and can be connected to existing ducting systems. And just like you can control a traditional heating system with a thermostat, you can do the same with a pellet stove, helping you get the most for your energy dollar. Hard-to-heat spaces In many homes there are some spaces that are just hard to heat properly. One alternative to reconfiguring your entire duct system is using a pellet burning stove to heat that space. Rather than piping heat to these areas on a regular basis, simply ignite your stove when the need arises.

Venting your Pellet Stove

Ideas for a pellet stove with Air Ducts? Can you hook up a pellet stove to ductwork Love pellet stoves that hook up to ductwork Follow this thread via email. I know how eager my environmentalist friends are to raise energy prices in order to carry out their pet projects but what are the sources of those costs that concern you?

I thought ducting a jacketed stove to the return might make better use of the heat. Fans could be used to vent it through.

Stove Pipe Not every home is designed the same way (i.e., having a fireplace built into a wall). When you want to install a wood stove or even a free-standing fireplace, you are going to need a way to get that wood-burning smoke and exhaust safely outdoors.

Proper Venting and Installation is Necessary for the Safety of Your Hearth Proper ventilation provides greater operating efficiencies with each stove, fireplace and insert, as well as providing a home that is free of potentially harmful by-products of burning fuel products. Proper installation is not only necessary for the performance of your new stove, fireplace or fireplace insert, but is necessary for your safety. We use our own technicians and installers who understand the importance of delivering legendary Ace service.

For more information and pricing on having Ace install a hearth in your Maryland home, click the price quote button below. Each appliance type gas, wood, pellet uses venting indigenous to that type. For detailed information on chimney systems, venting and installation, click the link below: Be sure there is access to the outside from the wall you choose. Pick the perfect mantel.

Finish your fireplace with one of many completely finished mantels. Direct Vent technology means you no longer need an expensive, elaborate chimney. Simply vent your fireplace through an outside wall. Direct Vent Gas Fireplaces Direct vent fireplaces, stoves, and inserts do not require a chimney and take just a few hours to install.

Your Pellet Stove is High Maintenance

You say you can be faithful and have a good time and for that I believe you, I truly do. The wood stove is great, a little bit of work, and can be a little messy, but I love having it.. If you get a pellet stove you have to buy the pellets.

Sep 29,  · Adding a wood stove to an oil furnace. Adding a wood stove to an oil furnace (post #) mbdyer on Sun, 09/11/ suggested a wood-burner that would hook-up to the furnace water plumbing and also heat the water. I’m not sure if pellet or log or both. double wall stove pipe up to the chimney (through the ceiling), then a commercial.

They also added cold air returns for the upstairs mfg home. The main floor heat runs are still the original foil backed fiberglass mat rectangular heat runs -not sheet metal. The restrictions have been based on non-code installations, space limitations, fire incidents, and reports of fires. Many insurance underwriters will not issue policies for wood burners at all, no matter how well installed.

And some of the “not approved” is simple attorney-talk. Issue 2 – I wanted to add the wood furnace in the basement at one end below bedrooms due to chimney location and wood supply. Can I just connect the hot air ducts from the wood furnace to the ends of the original upstairs heat runs, connect into the cold air return end above the wood furnace and use the wood furnace blowers?

Venting and blower system install for wood burning